Modifying your bathroom following practiced wheelchair accessibility guidelines is a great place to start any universal remodel. This will provide access for both wheelchairs and walkers. Furthermore, you can help avoid many future injuries. Any wet area like the bath is the most dangerous of all your home's surrounding living space and is the most common area for falls and slips. Simply getting in or out of the tub or shower, using the toilet and sink, or just maneuvering over wet surfaces can be hazardous to your health. Installing properly positioned grab bars to increase safety is a great place to spend your money on a limited budget around the shower, toilet, and tub.

     Traditionally bathroom vanities were constructed so the finished cabinet top was 30” AFF above finished floor.This meant that taller people had to bend over and stand away from the sink in order to use it.This puts added stress on the lower back and legs diminishing the comfort factor.Typically bathroom vanities are 21" deep and approximately 29" tall. The depth is not a problem but most folks would prefer a universal design height of 34". Sinks shouldn't be mounted higher than 34 inches from the floor to the top of the cabinet top for an under mount or drop in model. The sinks should not exceed six inches in depth and should be installed within three inches from the front of the overhanging cabinet top edge. The ADA vanity cabinet or even a simple wall hung sink should have a knee clearance below of 27 inches high and be at a minimum 30 inches wide by 11-25 inches deep. A 9" high clear kick area (by 6" deep) at the floor should be maintained for a full height cabinet and be approximately ten inches deep according to the cabinet depth. Remember twenty four inches is the maximum reach distance while sitting in a wheelchair. The choice of sink styles depends on the personal preference of the user. Be sure the lavatory controls are easily controlled with lever or paddle handles and are capable of being operated with one hand and not requiring tight grasping, pinching, or pinching of the wrist. Knobs, discs, or ball type handles can be hard to operate by anyone with soapy hands and more so by someone having an arthritic condition or other ailments. The closer the sink valves can be toward the front of the sink the better. This can be accomplished by following the curved outline of the sink.

     Bathroom cabinets vary by style and usability. There are basically two styles of ADA bathroom vanities that comply with an unobstructed 27" tall roll under area below the sink. ADA sinks with a rear drain location provide for better plumbing drain hook ups. This modification has everything to do with both the water supply lines and the waste line connecting the sink. There must be provisions made to protect the user from being scalded when coming into contact with any one of the plumbing pipes serving the sink. These connecting pipes may become heated merely by the water passing through them creating the problem. The open type model should always receive both waste and supply insulating jackets applied directly to the pipes providing protection for the wheelchair user. The closed model concealing the pipes will be equipped with a removable face or face board covering the pipes. This pipe concealing panel must be installed at the correct wheelchair user clearance angle. This allows for the needed unobstructed legroom required for the user. The vanity can extend beyond the sink but the area containing the sink is required to have this roll under capability. This section of the vanity top must not be any taller than 34 inches above the finished floor with sufficient lower leg clearance. Clear unobstructed reach distances around the counter top area must be observed. Any motion controlled sensors integrated into the various dispensing devices and/or plumbing fixtures throughout the restroom present a true hands free benefit to all the restroom users. If these aren't in the budget then at least wrist handles used for controlling the faucet can be incorporated into the design of the vanity.

     To assure a clear floor space the lavatory must be installed at 24" from any side wall measuring from the center line of the sink. The distance from one sink to another if using a double lavatory layout should be at least 30" center to center. In the case of wall hung freestanding sinks the minimum distance between them should be 4" between the sink edges.  The clear floor space of 30 by 48 inches must be provided for accessing all bathroom fixtures and these areas can overlap one another. The adjoining and overlapping wheelchair turning space should be an unobstructed sixty inches in diameter. A wheelchair turning space could utilize a T-shaped space considering a sixty inch square having two 12"x24" areas removed from each corner of the square from the same side. This will be a 36" wide base with two 36" wide arms. T-shaped wheelchair turning spaces can include on one arm. In this case the clear width at the cabinet should be 36" to use the space as part of the T-turn.

     Bathroom vanities with universal height cabinet tops and open knee spaces are taking over the marketplace. These new residential vanities do not need to look institutional even though they are wheelchair accessible. They can be designed like any other piece of fine furniture. Scalding must be guarded against by using either insulating pipe wrap or a removable panel for the plumbing.

     Many people find themselves needing accessible homes for themselves or family members. There are approximately 30 million Americans using wheelchairs and the number of people who need accessible homes will continue to increase as disabled and aging people are finding more ways to remain living in their homes. One important way to increase independent living is making a home accessible to an individual’s personal needs. Home modifications making homes wheelchair accessible can increase safety, accessibility, and independence for people who want to live independently.

     The toilet is a uniquely useful fixture in the bathroom for waste disposal.Toilets are typically chosen to match the rest of the plumbing fixtures within the room. These waste ridding devices have evolved very little over the years but require hand strength and agility to be operated correctly. They are not manufactured with accompanying handholds compounding to the difficulty of some users. The seat height of toilets is a critical consideration with respect to comfort and are now available in increased heights ranging from 18-19 inches in height eliminating the deep knee bend or back aches needed for seating. This is a wider accepted choice than the toilet heights we have grown accustomed to at 14-15”. Additionally raised or elevated seats can be installed if needed.  These will provide an additional five inches in height but the elevated seats will most assuredly cause problems if children are also using the facilities. However, lower seat heights are problematic and can also hinder the ease of transferring from a wheelchair and back again. Assisting electrical power toilet lifts with attached grab bars can help raise and lower the user if required. Grab bars should be installed on at least two sides of the toilet. All grab bars must be secured into either adequate wood blocking or existing wall studs so they can hold at least 250 pounds of downward force. Creating a toilet within an open area which is approachable from both sides and not in a closet is much more accessible. Accessible toilets should never be placed in small alcoves. The old idea of placing them within a private room works well for those with a full range of mobility.  They should have a minimum clear width of 60" optimally and sufficient space to accommodate a wheelchair to the sides of the toilet or in front for transferring to and from the toilet. Toilet seats are also available with a heat feature and some have the ability to self-close or have a night light. Wall mounted toilets offer more accessible areas underneath for cleaning versus floor mounted models but are more expensive and not a readily available. An add on bidet attachment installed on a regular toilet can be handy and help improve hygiene especially when a caretaker is involved.  This is a cheaper idea than a free standing bidet and also concerns precious space.

     Toilets need to have the flush handle located toward the middle of the room and be of the correct height for comfort. Proper clearance from any walls (18" from any side wall to the center of the toilet) must be observed and the clear 30 inch by 48 inch approach to the toilet must be maintained. Grab bars should be installed both on the rear and sidewall of the toilet at 34 inches above the floor. If no side wall is present within a reasonable reach distance from the toilet then you can opt for a folding model as in the above photo.  Any bathroom transformation needs to include universal design characteristics and be accessible to everyone in the home.

     Designing task oriented bathroom fixtures without consideration for their use, placement, or how they make up the bathroom environment makes up the current way of thinking universally.  The tub/shower, sink, and toilet are used individually and designing for the greatest approach clearance within clear spaces.  Observing minimal distance to traverse for each fixture location should take president within any accessible design.  This individual design will provide the greatest use of each fixture for the bathroom layout.  Emphasis must be placed on fixture placement to accomplish certain tasks but grouping these tasks where possible can be beneficial to everyone. The greater the proximity of the fixtures, the more efficient and convenient the design.  The universal bathroom can be a more enabling environment focusing on an individual’s capabilities with regards to the individual’s surroundings.

     Problems encountered while accessing your home when you are wheelchair bound generally begin before or at the front door.  If you can reach the front porch approach without obstruction then you have a great start since the stairs leading onto the front porch can be another matter all together.  A correctly designed ramp having a 1:12 slope can adequately solve this problem.  The use of grab bars and any railings will be dictated by the ramp's design and the regulations and physical limitations involved.   Once your safely upon the porch, your home's front door width can become an issue.  Any entry door less than three feet in width will cause a problem in maintaining a required 32 inch clear entry way which starts the new accessible route within your home.  Rolling over any vertical threshold height greater than 1/2" is also difficult to maneuver.  Once inside the structure a new set of problems concerning your accessibility will be discovered.

     A traditional home builder has never truly considered the special needs of the disabled or aging within any home design. Unfortunately the design emphasis is always put on aesthetics and takes for granted everyone's mobility.  There certainly are no guarantees or clauses within any home's sales contract that will prevent our future personal life experiences from  introducing us to at least a temporary disability.  Accidents will always happen and you could find yourself having to utilize a wheelchair or walker to facilitate your independence for mobility.  Limitations in our mobility or constantly changing needs experienced by both the disabled and the elderly have sprung a new dimension in construction known as ADA remodeling to accomplish increased accessibility.  Our homes have always been exempt from any and all of the accessibility regulations that have been put in place since 1968 when our Viet Nam veterans were returning home. The new evolving concept known as Universal Design for home remodeling is catching on nation wide and has been for several years as a sign of the times.  Universal design techniques used in building makes a home more accessible to all regardless of their mobility or adaptive abilities. An evolution of new products used for disability home modifications is making those homes more accessible and has finally come about in the remodeling industry.  These new advances in accessible home remodeling in Austin not only keep the living environments safer but will not compromise the home's aesthetics. 

     An accessible bathroom for the user's convenience and safety becomes the first issue for anyone using a wheelchair or walker for either a short time while recovering or for the rest of their life.  The disability access bathroom will be located within the home's accessible route.  Any architectural barriers encountered while approaching the bathroom entrance will need to be removed.  The minimum clear widths have to be observed.  This will include the bathroom door itself.  Twenty four to twenty eight inch wide doors are commonly used during the construction of American homes for accessing the bathroom.  However, anything below three feet does not meet the 32 inch required clear width needed for clearance of a wheelchair. This work may involve framing alterations and moving light switches.  The electrical changes should be done by a licensed electrician assuring your safety.

     A completely serviceable special needs bathroom must contain at least one ADA vanity and the accessible route must be defined.   The vanity must be one with a clear underneath scald protected area having an unobstructed roll under capability for wheelchairs.  These new residential vanities do not need to look institutional.  They can be designed like any other piece of fine furniture.  A five foot turning radius allowing the wheelchair to maneuver into any approach must also be associated with the ADA vanity.  A 36x48" clear approach area to the vanity must be observed and this can overlap the five foot turning radius.  The area of travel will then be enhanced by an unobstructed clear accessible barrier free route dedicated to reaching the vanity. 

     Bathroom cabinets in Austin vary by style and usability.  There are basically two styles of ADA bathroom vanities that comply with an unobstructed 27" tall roll under area below the sink.  ADA sinks with a rear drain location provide for better plumbing drain hook ups.  This modification has everything to do with both the water supply lines and the waste line connecting the sink.  There must be provisions made to protect the user from being scalded when coming into contact with any one of the plumbing pipes serving the sink.  These connecting pipes may become heated merely by the water passing through them creating the problem.  The open type model should always receive both waste and supply insulating jackets applied directly to the pipes providing protection for the wheelchair user.  The closed model concealing the pipes will be equipped with a removable face or face board covering the pipes.  This pipe concealing panel must be installed at the correct wheelchair user clearance angle.  This allows for the needed unobstructed legroom required for the  user.  The vanity can extend beyond the sink but the area containing the sink is required to have this roll under capability.  This section of the vanity top must not be any taller than 34 inches above the finished floor with sufficient lower leg clearance.  Clear unobstructed reach distances around the counter top area must be observed.  Any motion controlled sensors integrated into the various dispensing devices and/or plumbing fixtures throughout the restroom present a true hands free benefit to all the restroom users.  If these aren't in the budget then at least wrist handles used for controlling the faucet can be incorporated into the design of the vanity.  Furthermore, automatic flush valves should be used on all toilets and urinals that provide for hands free use.

     Finding a contractor familiar with the guidelines of Elder construction and accessibility remodeling can be quite difficult. Be sure to check out the credentials of any potential bidders you contact.  Be sure they understand that the alterations you are seeking are for wheel chair accessible home remodeling and modifications.  Furthermore be sure this person knows and practices both the federal and most importantly your state's requirements before entering into any contract.

     Aging in place home modifications are available through T-Square Company. We are a certified aging in place (CAPS) specialist.  Each design/build situation will be customized to fit your personal needs. Call 512-444-0097 today to begin the accessible second chapter of your life while remaining safe and secure in your existing home. CAPS #1636580

     Let's face it, accessible homes are needed by all of us at some time in our lives.  This is true whether it's for ourselves, a family member, or a guest.  The need is certainly not driven by age but is a result of life's experience.  Any family living with disability among any of the generations within it's group can always benefit from additional accessibility.   This will in turn increase safety and independence for all involved as they go through life. 

       Disability is a complex phenomenon representing an interaction between one's physical impairments, the activities they need to perform, and the architectural barriers within the space in which this situation occurs.  The terminology and jargon used for disabilities evolves regularly whereas, "handicapped" is no longer acceptable.  It is no longer merely a description of intellectual or physical impairments.  Each individual with similar impairments describes his or her limitations differently.  The blind don't experience their world the same as a person with deafness. Some of our societal statistics that weigh into aging in place situations include reports stating that 19% of the population between the ages of 16 and 64 and 42% of those of us 65 and over have a physical disability affecting the activities of their daily lives.  For a progressive condition,  aging in place home remodeling in Austin definitely comes into play.  This is the only way to insure both the safety and mobility for the homeowner or family member requiring the home modifications.  The two main groups driving this aging in place market are those people who are 65 and over and the baby boomers.  The first group is projected to reach 55 million in 2020.  The baby boomer generation born between 1946 and 1965 today make up 28% of the U.S.  population and are made up of some 77 million people.  Modifications of existing homes is important because people of age 50 and older want to remain in their current home for as long as possible.  Aging in place home modifications in Austin should only be done by a CAPS certified remodeling company.  This is the only way that you can be assured that the home modifications are the right choices to satisfy your needs.  There is no need to waste money only to find out that the wrong alterations were done by an inexperienced and unqualified remodeling company.  Always check their credentials to verify that the remodeler holds a CAPS certification. All registered CAPS program graduates and their remodeling company will be listed in a national registry in Washington.  The information can be found by simply visiting nahb.org/CAPS.

     The concept of the accessible home has evolved beyond the basic grab bars and ramps to one in which accessibility is built into the basic design.  Universal design makes living in a home easier for people of all ages and abilities.  Accessible home remodeling for the disabled can be both beautiful and functional and never needs to have any institutional appearance.  As our aging baby boomer population ages, the need for accessibility remodeling in the home is becoming ever more important.  Our new way of viewing the basic home in our society and our antiquated architecture is giving way to a revolution in home design.  Ordinary homeowners with extraordinary challenges can partner up with CAPS design professionals, architects, and their own families to create homes to restore capabilities, independence, and grace to daily living. Fortunately there is home accessibility help in Austin, Texas for our veterans.

     Everyone ages differently and has different needs and wants.  The factors that constitute the aging in place market for all individuals are based on a persons genetic makeup, their lifestyle including the choices they have made while living their life, and their environment.  These factors have brought about the need for universal design.  This is the design of products, services, and environments that are usable by as many people as possible regardless of age, ability, or situation without the need for adaptation or specialized alterations.  It provides for the greatest safety and access for any home guests or occupants and is undetectable when done well.  Since so very few homes share the accessibility offered by universal design, to satisfy the needs of a particular household member brought about by an accident, an illness, or simply the aging process there will always be a need for customized accessibility features.  This will be accomplished by a CAPS accredited remodeling professional producing a truly functional design when considering accessible home designs in Austin, Texas and disability access baths.   T-Square Company is a competent home remodeling company who understands and practices aging in place home modifications in Austin. They are CAPS certified and will perform the work needed to fit their in house design insuring your safety and accessibility during a handicap remodeling project. T-Square Company specializes in accessible bathrooms in Austin, Texas.

     Physical limitations affect many more people than the daily users of walkers and wheelchairs.  Many members of our life experienced or elder society have significant problems in dealing with their home environment.  Today's conventional building standards conflict with most people's accessibility when you consider our created architectural barriers concerning cabinetry and door opening widths, individual strength, range of motion, movement, manual dexterity, balance, and coordination. Once the demands of our built environment exceed their capacities we become excluded from a room or even the entire home bringing forth the need for elder construction and remodeling.  The building world must work in unison to be sure the entire living environment meets basic needs in addition to affordability and structural integrity for the consumer and home owner.  This includes both the home and the components within the home being accessible to all inhabitants.  Privacy, sense of belonging, sense of control, and the sense of safety and security make up the quality of life for any home and should be considered for any design.

     There are really three categories of aging in place customers.  Those who are simply and wisely planning ahead for their futures to remain in their present homes.  The second category concerns those people who know they have a chronic medical disorder and need to prepare in advance for accessibility issues which will come as a result of their disease.  People with diseases that are constantly causing increased physical or mental changes to their being are a good representative of this second group.  The third group involves those people who either have had a chronic problem that has  progressed severely altering their mobility or those who have sustained a life altering tragedy such as being involved in an accident.  All of these groups will drive the future metamorphosis of existing inaccessible dwellings.

     Accessible wheelchair designs in Austin are available through T-Square Company. Each design/build situation will be customized to fit your personal needs. Call 512-444-0097 today to begin your accessible second chapter in your life while remaining safe and secure in your existing home. CAPS 1636580

Disability Bathroom Remodels In Austin, Texas